Manufacturer |
Product Name
|
Classification Name
|
Kyowa Electronic Instruments
|
INSTRUMENTATION AMPLIFIER WGA-680A
The WGA-680A series is compact, low-cost
instrumentation amplifiers enabling
direct reading of physical quantities
such as load through high-speed sampling of
signals from a strain gage transducer.
*Substantial comparison functions
(Extra high, high, OK, low, and Extra low)
*Various optional interfaces(CC-Link,
RS-485/ TEDS, RS-232C/TEDS, and BCD/TEDS)
♦ Sampling speed : 4000 times/s
♦ A/D converter : 24 bits
|
Kyowa
STRAIN GAUGE & RELATED INSTRUMENTS
|
Kyowa Electronic Instruments |
TENSION/COMPRESSION LOAD CELL LUK-A
Thin design makes the LUK-A suitable
for installation to height-limited space.
The fatigue life can be extended
by using at lower than half the rated
capacity if load is applied continuously
and repetitively.
*Highly accurate and stable
*Inert gas-sealed hermetic structure
♦ Rated capacity : ±5kN to ±2MN
♦ Nonlinearity : ±0.1 to ±0.2%R.O
♦ Rated output : ±2mV/V
♦ Safe overload rating : 150%
♦ Protection rating : IP64
|
Kyowa LOAD CELLS
|
Kyowa Electronic Instruments |
STAINLESS STEEL LOAD CELL LCTS-B
Developed for weighing hoppers and tanks,
the S6 load cell has a built-in bracing
mechanism. The strainless steel structure
makes it usable under environment where
it is exposed to moisture and corrosive gases.
The thin design with top and bottom
plates integrated facilitates installation
to hopper bracket and tank foot.
The bracing function makes it suitable
for weighing stirrer- or leg-equipped tanks.
♦ Rated capacity : 5 to 100kN
♦ Nonlinearity : ±0.03% R.O
♦ Rated output : 2mV/V
♦ Safe overload rating : 150%
|
Kyowa LOAD CELLS
|
Kyowa Electronic Instruments |
COMPACT TENSION/COMPRESSION
LOAD CELL LUX-B-ID
The LUX load cell is suitable for load
measurement and control of small presses
and press-fitting machines. The compact,
lightweight and stainless steel structure
with screw-shaped load receiving part
enables easy incorporation into equipment.
In addition, the connector-equipped design
ensures easy installation of the mainframe
free from the cable as well as facilitates
cable replacement.
♦ Rated capacity : ±50N to ±20kN, 9 models
♦ Nonlinearity : ±0.1 to ±0.15%R.O
♦ Rated output : 0.9 to 1.3mV/V
♦ Safe overload rating : 150%
|
Kyowa LOAD CELLS
|
Kyowa Electronic Instruments |
BEAM-TYPE LOAD CELL LUB-B
The accuracy is as high as 1/3333
with the rated capacities of 50 to 500N
and both the body and bellows
are made of stainless steel with rated
capacities of 1 to 20kN.
The LUB-B enables configuration of
accurate and reliable weighing systems
for conveyors and tanks.
*Compact and lightweight
*Metal bellows adopted for reliable
performance
♦ Rated capacity : 50N to 20kN
♦ System accuracy : ±0.03%R.O
♦ Rated output : 2mV/V
♦ Safe overload rating : 150%
|
Kyowa LOAD CELLS
|
Kyowa Electronic Instruments |
WASHER-TYPE LOAD CELL LCW-C
The extremely simple structure facilitates
handling and maintenance. Varieties of
models available in this series include
a small diameter type for measurement of
bolt tension and press forming load
and an inert gas sealed, highly stable
type for rolling mills operating under
severe environment.
*Thin and highly stable
*Various rated capacities available
♦ Rated capacity : 10kN to 5MN
♦ Nonlinearity : ±1%R.O
♦ Rated output : ±1mV/V
♦ Safe overload rating : 150%
|
Kyowa LOAD CELLS
|
Kyowa Electronic Instruments |
FIBER OPTIC INSTRUMENT EFOX-1000 SERIES
The EFOX-1000 series is a fiber optic
instrument which has the industry-leading
measuring accuracy and stability.
The high response enables multi-point
measurements easily. The EFOX-1000
series is also able to support
long-distance measurements.
*NIST traceable
(Waveform calibration function)
*Scan frequency : Max. 1000 Hz
*High scanning frequency measures
dynamic phenomena.
*Single optical fiber measures multi-point
measurements and various measurements.
*Strong against electromagnetic noises.
*Non-flammable and lightning protection
♦ Measures FBG sensors : Max. 160 channels
|
Kyowa STRAIN GAUGE & RELATED INSTRUMENTS
|
Kyowa Electronic Instruments |
MULTI SIGNAL CONDITIONER MCF-A
The MCF-A is a multi-signal conditioner
which is usable in various fields.
The MCF-A builds the measuring system
that matches the purpose by selecting
necessary conditioner cards.
*All operations are available on the
front panel.
*Various conditioner cards for various
sensors.
*Compact and lightweight than the
conventional products.
*I/O isolated
*Various fixing fixtures and handles.
♦ 8 channels or 16 channels
♦ Digitally indicates the output voltage of
any one channel.
|
Kyowa STRAIN GAUGE & RELATED INSTRUMENTS
|
Kyowa Electronic Instruments |
MINIATURE PRESSURE SENSOR PS-C
The PS-C is a small and ultra-thin pressure
transducer which has a bridge of strain
gage it in. The cable pull-out direction
is parallel to the sensing surface.
The PS-C is suitable for measuring
distributed pressure by using multiple
PS-C units.
*Ultra-thin
*Installable in a narrow area.
*Various capacity range.
*Installed by adhesive.
♦ Rated capacity : 50kPa to 7MPa
♦ Temperature compensation : 0 to 50°C
|
Kyowa PRESSURE TRANSDUCERS
|
Kyowa Electronic Instruments |
DIGITAL TELEMETER MRS-100 SERIES
The MRS-100 series is a telemeter based
on the digital modulation system.
The radio communication distance of max.
50m enables labor saving. The compact
transmitter, compared to the conventional
products, allows installation in a narrow
area.
*Certified in wireless regulation in Japan,
U.S.A., and India.
*Easy operation without PC after initial
setting
*Information functions including reception
intensity, transmitter battery voltage
check, and communication error check.
*Dual antennas enhance the communication
reliability. (Diversity reception)
♦ Radio communication distance : 50m
♦ Sampling frequency : 4.8kHz
|
Kyowa STRAIN GAUGE & RELATED INSTRUMENTS
|
Kyowa Electronic Instruments |
POTENTIOMETER-TYPE DISPLACEMENT TRANSDUCER DTT-A/DTS-A
DTS-A is a strain gage type displacement
transducer.
DTT-A is a potentiometer-type displacement
transducer.
They can widely be used for measurement of
structural relative displacement or
absolute displacement from a steady point.
*Both tension and compression
*Fast response
(DC to 50Hz when the tip is fixed)
♦ Rated Capacity : 100mm
♦ Nonlinearity :
[DTT-A] Within±0.2%R.O ;
[DTS-A] Within±0.3%R.O
♦ Repeatability : 0.1%R.O or less
♦ Weight : Approx. 110g (Excluding cable)
|
Kyowa DISPLACEMENT TRANSDUSERS
|
Kyowa Electronic Instruments |
COMPACT RECORDING SYSTEM EDX-10 SERIES
Measuring instruments that measure simply
by being connected to a PC using the USB
interface.
The EDX-11A and EDX-14A that measure
with strain gage type transducers,
pressure, displacement, etc.
The EDX-12A that measure voltage,
the EDX-15A that measure force, pressure,
displacement, and voltage, and the EDX-13A
that measure temperature with a thermocouple.
*Up to 4 measuring units can be powered
by USB interface, no separated power
supply is required
*With stacked connection, no synchronization
cable is required, therefore wiring-saving
*Max sampling frequency 20kHz for 4 channels
of a single measuring unit in sync
|
Kyowa STRAIN GAUGE & RELATED INSTRUMENTS
|
Kyowa Electronic Instruments |
CARRIER TYPE INSTRUMENTATION AMPLIFIER WGA-120A
Compact, lightweight and affordably
priced carrier instrumentation amplifier
that is suitable for measurement of load,
pressure, torque or displacement in
combination with a strain-gage transducer.
*Strong against inverter noise
*Rich in lineup for variety applications
*Voltage/current output switchable
|
Kyowa STRAIN GAUGE & RELATED INSTRUMENTS
|
Kyowa Electronic Instruments |
COMPACT DIGITAL INDICATOR WDS-190AS1/191AS1
A Compact Digital Indicator powered by
dry batteries. Suitable for measurement,
management and checking of force, load,
pressure or displacement transducers.
*lightweight, approx. 110g
*With auto backlight and anto
power-off functions
*Operates for about 72 hours
|
Kyowa STRAIN GAUGE & RELATED INSTRUMENTS
|
Kyowa Electronic Instruments |
MEMORY RECORDER/ANALYZER EDX-5000A
The EDX-5000A is an advanced all-in-one
measuring instrument having sophisticated
features and high-speed processing
capabilities. The EDX-5000A records
data and video, and it performs rosette
analysis and other arithmetic operations
simultaneously. The equipped touchscreen
enables operations without a keyboard.
*Single unit measures max. 80 analog channels.
Synchronous measurements :
Max. 800 channels by using ten units
*Built-in battery for momentary power loss
*Effective real-time processing capability
♦ Sampling frequency :
Max. 200 kHz / 32 channels
|
Kyowa STRAIN GAUGE & RELATED INSTRUMENTS
|
Kyowa Electronic Instruments |
STRAIN AMPLIFIER DPM-900 SERIES
Strain Amplifier with high stability and
accuracy. Simple operation vastly reduce
the working hours.
♦ Stability : Temperature
Zero point : ±0.1μm/m per °C
Sensitivity : ±0.05%/°C
Time
Zero point : ±0.5μm/m per 24h
Sensitivity : ±0.2%/24h
Power supply
Zero point :
±0.05%F.S/power supply variation ±10%
Sensitivity :
±0.05%/power supply variation ±10%
♦ Frequency Response Range :
DC to 2.5kHz (DPM-911B), DC to 5kHz (DPM-912B),
DC to 10kHz (DPM-913B)
|
Kyowa STRAIN GAUGE & RELATED INSTRUMENTS
|
Kyowa Electronic Instruments |
SMALL-SIZED TRIAXIAL ACCELEROMETER AMA-A
Compact and lightweight acceleration
transducer enduring large overloads.
*Fault diagnosis function is available
*Power supply from conditioner cards
CVM-41A or AD-40AS
♦ Rated Capacity :
±19.61 to 土98.07m/s2
♦ Safe Overload :
±9800 to ±19613m/s2
♦ Frequency Response Range :
DC to 500Hz (AMA-A-2/5)
♦ Dimensions :
Sensor 14(W)×10(D)×6(H)mm
Relay 30(W)×21(D)×9(H)mm(AMA-A-2/5)
|
Kyowa VIBROMETERS, ACCELEROMETERS
|
Kyowa Electronic Instruments |
HIGHLY RELIABLE PRESSURE TRANSDUCER PHS-B
Usable at Both High and Low Temperatures,
Possible to Measure Absolute Pressure.
*High stability at high temperature
*Possible to measure absolute pressure
♦ Rated capacity : 200kPa to 20MPa
♦ Temperature effect on output :
Within ±0.015%/°C
♦ Nonlinearity : Within ±0.2%R.O
♦ Safe overload : 150%
♦ Mounting screw : G3/8, male
|
Kyowa PRESSURE TRANSDUCERS
|
Kyowa Electronic Instruments |
COMPACT HIGH-TEMPERATURE PRESSURE TRANSDUCER PHF-S-S1
A Small-sized High-temperature Pressure
Transducers. Easily wire and replace the cable.
UNF and G type screws are available
from size 8 to 12mm.
*After removing the connector, enables to
install in a limited space by a socket wrench
♦ Rated Capacity : 2 to 20MPa
♦ Compensated Temperature Range : -40 to 150°C
♦ Degree of Protection : IP45 (IEC 60529)
♦ Safe overload rating : 150%
|
Kyowa PRESSURE TRANSDUCERS
|
Kyowa Electronic Instruments |
WIRE-TYPE DISPLACEMENT TRANSDUCER DTPA-A
Wire type, therefore long displacement
measurement is possible.
*Hardly kinking wire
*High response (When the stroke is
rated output : 1000 mm/s or equivalent)
*New wire-winding mechanism enables
less trouble
*Compact, lightweight, and easy to install
*Constant measuring force
*Measurement possible with strain amplifiers
♦ Rated Capacity : 500mm, 1000mm, 2000mm
♦ Nonlinearity : Within ±0.3%R.O
♦ Repeatability :
0.1%R.O or less (DTPA-A-500, DTPA-A-1000)
♦ Weight : Approx. 220g
(DTPA-A-500, DTPA-A-1000 Excluding cable)
|
Kyowa DISPLACEMENT TRANSDUSERS
|
Kyowa Electronic Instruments |
HIGH-SPEED, COMPACT INDICATOR WGI-470AS1
The WGI-470AS1 is a compact general-purpose
low-cost instrumentation amplifier providing
basic functions required for measurement
in combination with a strain gage transducer.
This is equipment can measure a press load
by using a high-speed digital peak hold
and it also can use a wide range of
measurements and controls such as load
measurement, etc. by using high resolution.
♦ Sampling Rate : 2000times/sec
♦ Size : 48×96mm
♦ Display : 5digits, Polarity LED
♦ Comparison Judgment : 3 (HIGH, OK, LOW)
♦ Holding : 5types, Digital peak hold
♦ Analog Output : Voltage and current
(simultaneously)
|
Kyowa STRAIN GAUGE & RELATED INSTRUMENTS
|
Kyowa Electronic Instruments |
SMALL-SIZED COMPRESSION LOAD CELL LMC-A
Compact and lightweight load cells
can be used by merely placing or bonding
on the load site, setting in a hollow,
or affixing with a mounting band.
Major applications include measurement of
load distribution by using multiple units,
load measurement in pipe making mills,
or where a measuring site or the weight
of the load cell itself is limited.
*high output accuracy
*Suitable for load distribution measurement
♦ Rated Capacity : 5 to 50kN
♦ Nonlinearity :
Within±1% R.O(5kN, 10kN : Within±0.5% R.O)
♦ Repeatability : 0.5% R.O or less
♦ Rated Output : 1.5mV/V (3000μm/m) or more
♦ Safe Overload Rating : 150%
♦ Size : 5kN, 10kN φ12, 20kN φ16, 50kn φ22
|
Kyowa LOAD CELLS
|
Kyowa Electronic Instruments |
PORTABLE VEHICLE WEIGHING SYSTEM RWP-700A RWP-750A
A portable system to weigh and manage
truck loads. It consists of the detectors
that detect the truck weight by weighing
the load of each wheel on the platform
and the indicator that indicates,
records and prints out the weighing result.
*USB memory for transferring data to PC
*Also available in wireless connecting type (RWP-750A)
♦ System composition : Indicator ×1 and Detector ×2
♦ Number of applicable axles up to 7 Detector
♦ Rated Capacity : 7500kg per unit
♦ Degree of Protection : IP67 (IEC 60529)
Indicator
♦ Indication Unit : 10kg
♦ Measurement Modes : Stop mode (Recommended),
running mode (5kg/h Max.)
|
Kyowa AXLE AND PORTABLE LOAD METER TRUCK WEIGHING SYSTEM
|
Kyowa Electronic Instruments |
SMALL-SIZED COMPRESSION LOAD CELLS LMB-A/LMBT-A
These ultra-small and lightweight
load cells can be used by merely placing
it on the subject site or setting
in a hollow. The LMBT-A can be used
at high temperatures up to 100°C.
*Suitable for load distribution measurement
*TEDS-installed option available
*Usable at up to 100°C(LMBT)
♦ Rated capacity : 50N to 2kN
♦ Nonlinearity : ±0.5%R.O/±0.3%R.O
♦ Repeatability : 0.3%R.O
♦ Rated output : 1.4mV/V
♦ Safe overload rating : 150%
♦ Outer diameter : φ10 mm/φ16 mm
|
Kyowa LOAD CELLS
|
Kyowa Electronic Instruments |
THIN COMPRESSION LOAD CELL LCK-A
The LCK-A series load cells have excellent
accuracy, reliability, stability,
and response. They also have a thin design
for convenient installation as detection
terminals of weighing systems.
This thin design makes them suitable
for applications such as conveyors,
vehicles, cranes, hoppers, and tanks
where the space, especially the height,
is limited and the detecting part needs
to be downsized.
*Thin Design
*High Reliability
*Hermetically-Sealed Structure with
Inert Gas Filled in
♦ Rated Capacity : 5 to 200kN
♦ Nonlinearity :
Within±0.2%R.O(200kN : Within±0.5%R.O)
♦ Repeatability : 0.05% R.O or less
♦ Rated Output : 2 mV/V±0.5%
♦ Safe Overload Rating : 150%
|
Kyowa LOAD CELLS
|
Kyowa Electronic Instruments |
BUILT-IN AMPLIFIER TORQUE TRANSDUCER TPS-A
*Built-in amplifier enables ±5V output
*Non-contact design requires less
maintenance
*Provides rotation speed output
*Compact and lightweight
♦ Rated capacity : ±0.1N・m to ±5kN・m
♦ Nonlinearity : ±0.1%R.O (TPS-A-01NM to 2NM)
♦ Rated output : ±5V
♦ Rotation speed output : 4pulses/rotation
♦ Maximum speed : 15000rpm (TPS-A-01NM to 2NM)
|
Kyowa TORQUE TRANSDUCERS
|
Kyowa Electronic Instruments |
INSTRUMENTATION AMPLIFIER WGA-910A
The WGA-910A is an instrumentation
amplifier for monitoring phenomena,
which is hard-to-know in digital formats,
in waveforms by mounting in factory
automation units. The equipped TFT LCD
widens the viewing angle than the
conventional products.
*Touchscreen
*Displays waveforms, numerical values,
and enlarges numerical values.
*Various interfaces (CC-Link, RS-485,
RS-232C, BCD output)
*Compatible with SD cards and saves
waveform data.
*Comparison determination results
are color-coded.
*Compatible with TEDS
♦ Sampling speed : 4000 times/s
♦ A/D resolution : 24 bits
|
Kyowa STRAIN GAUGE & RELATED INSTRUMENTS
|
Kyowa Electronic Instruments |
SMALL-SIZED PRESSURE TRANSDUCERS PGL-A/PHL-A
These compact, lightweight and stable
sensors are suitable for pressure
measurement in installation-space-limited
places. The semi-flush diaphragm ensures
excellent response and dynamic characteristics.
The PHL-A can widely be used at high
to low temperatures.
*Highly stable and quick response
*Usable in a wide temperature
range of -196 to 210°C (PHL)
*Connector type and cable-integrated type
♦ Rated capacity : 1 to 10MPa
♦ Nonlinearity : ±0.3 to ±0.5%R.O
♦ Safe overload rating : 150%
♦ Mounting screw : G1/8, male
|
Kyowa PRESSURE TRANSDUCERS
|
Kyowa Electronic Instruments |
SENSOR CHECKER WDS-500B
This pocketable unit enables easy
checking of transducers and amplifiers.
*Provides sensor connector and amplifier
connector
*Strain, input/output resistance or
insulation resistance can be measured
through a press of the key
*Strain output enables checking of
amplifier
*Can display TEDS information of
TEDS-installed transducer
*Compact and lightweight
(69×115×28mm, approx. 220g)
*Operates on 2 AA size dry cells for
approximately 8 hours
|
Kyowa STRAIN GAUGE & RELATED INSTRUMENTS |
Kyowa Electronic |
PGM-200KE-20MPA |
Kyowa
(20 MPa (Capacity Pressure Sensor) |